A fuel-cell/battery hybrid DC backup power system via a new high step-up three port converter

In this paper, a fuel-cell (FC)/battery hybrid direct-current (DC) backup power system is proposed for high step-up applications. This system is composed of a newly developed non-isolated three-port converter, which achieves a high voltage gain by taking the advantage of a quasi Z-source network and an energy transfer capacitor. After analyzing the converter, a comprehensive comparison study and a design procedure are provided. Moreover, the controllers regulating the source power levels while smoothing the FC power profile according to the proposed energy management strategy (EMS) are designed based on the developed small-signal model of the proposed converter. Both hardware and controller design procedures are validated through the PSIM model of the whole system. As a result, it is shown that the proposed system can effectively couple FC and battery while transferring their energies to a high voltage DC bus according to the offered EMS.     

Lightweight reactor design by additive manufacturing for preheating applications using metal hydrides

Thermal energy storage systems based on metal hydrides can be a solution for preheating fuel cells (FCs). They can provide thermal energy at temperatures below −20 °C during startup, while heat at 50 °C during operation is sufficient for regeneration. The challenge of such a system in mobile applications is the final weight specific thermal power. In this study, a reactor design based on additive manufacturing techniques for ~300 g of metal hydride is presented. Here, a reactor (passive) to hydride (active) mass ratio of 0.97 is realized, still reaching high weight specific thermal power of up to 2.1 kW/kg_MH at −20 °C and 8 bar (LmNi_4.91Sn_0.15). Considering the example of preheating a FC from −20 °C in ~120 s, the performance of LaNi₅ and LmNi_4.91Sn_0.15 is studied. While LaNi₅ requires higher regeneration temperatures than LmNi_4.91Sn_0.15 (>40 °C compared to >20 °C), its performance is less sensitive to operative variations due to its nearly ideal thermodynamic characteristic.     

The addition of spices and herbs to vegetables in the National School Lunch Program increased vegetable intake at an urban,economically-underserved,and predominantly African-American high school

Vegetable intake is far below recommendations among African-American adolescents living in economically-underserved urban areas. While the National School Lunch Program (NSLP) helps overcome access barriers, vegetable intake remains challenging and novel interventions are required. A two-year, multi-phase, school-based intervention was conducted at an urban, economically-underserved, and predominantly African-American high school in Baltimore, Maryland to determine whether stakeholder-informed addition of spices and herbs to NSLP vegetables would increase intake. The stakeholder engagement phase included assessment of NSLP vegetable attitudes/preferences among 43 school stakeholders and subsequent student sensory testing. The second phase was conducted in the school cafeteria and consisted of eight weeks comparing student intake of typical vegetable recipes versus otherwise-identical recipes with spices and herbs. 4570 student lunch plates were included in the vegetable intake comparison. Vegetable intake was measured by lunch tray plate waste. Willingness to try vegetables was assessed by the difference between plate waste and estimated mean vegetable served weight. Intake of typical vegetable recipes and vegetable recipes with spices and herbs was compared with student’s t-test. Chi-square test was used to compare willingness to try vegetables. Total vegetable intake was 18.2% higher (8.22 g per meal, p < 0.0001) with spices and herbs than with typical recipes. There were no differences in trying vegetables with spices and herbs, although student-led advocacy was associated with increased trying vegetables with spices and herbs (78.8% with advocacy, 67.5% without advocacy, p < 0.0001). The addition of spices and herbs to vegetables in the NSLP was feasible and associated with small increases in vegetable intake at an urban, economically-underserved, and predominantly African-American high school.     

Design and computational analysis of a metal hydride hydrogen storage system with hexagonal honeycomb based heat transfer enhancements-part A

In this study, design and performance analysis is carried out for a 10 kWh metal hydride based hydrogen storage system. The system is equipped with distinctive aluminium hexagonal honeycomb based heat transfer enhancements (HTE) having higher surface area to volume ratio for effective heat transfer combined with low system weight addition. The system performance was studied under different operating conditions. The optimum absorption condition was achieved at 35 bar with water at room temperature as heat transfer fluid where up to 90% absorption was completed in 7200 s. The performance of the reactor was observed to significantly improve upon the addition of the HTE network at a minimal system weight penalty.     

Microstructure characterization and compressive performance of 3D needle-punched C/C–SiC composites fabricated by gaseous silicon infiltration

3D needle-punched C/C-SiC composites were fabricated from carbon fiber reinforced carbon (C/C) preforms, with densities of 1.05?g/cm³ and 1.28?g/cm³, by the gaseous silicon infiltration (GSI) method at fabrication temperatures from 1500?°C to 1800?°C. The compressive strengths and elastic moduli in transverse direction are larger than those measured under longitudinal compression except that samples fabricated from 1.28?g/cm³ density exhibit lower elastic moduli in transverse direction than in longitudinal direction. The compressive strength and modulus increase with fabrication temperature at 1500?°C and 1600?°C, and then decrease with higher fabrication temperature. Samples fabricated from the lower density C/C preforms have greater compressive strength and modulus. X-ray tomography was applied before and after the mechanical tests to characterize the microstructure and damage patterns, and the results indicated that for C/C-SiC composites fabricated at 1700?°C from 1.28?g/cm³ density C/C preform the matrix has a volume fraction (vol%) of 36.9%, and the initial intra-bundle cracks (0.6?vol%) display a space crossing structure while the inter-bundle pores (6.0?vol%) are special irregularly distributed.     

Utilization of linseed cake as a postagricultural functional filler for poly(lactic acid) green composites

Linseed cake (LC), a byproduct of linseed oil extraction, is used as a functional filler for production of biodegradable composites. To determine the influence of residual linseed crude oil contained in lignocellulosic filler on the properties of the poly(lactic acid) (PLA)-based composites with 5–30% filler content, two types of LC were analyzed: a defatted and an unmodified one. Complex analysis of the composites' properties change was conducted in relation to their structure modification caused by the addition of a waste filler. It was found that the addition of LC resulted in simultaneous plasticization and improved crystallization of PLA. Lignocellulosic particles and crude linseed oil contained in the LC powder provided a modifying effect, influencing the level of crystallinity and mechanical and thermomechanical properties. Using LC may thus overcome one of the main drawbacks of PLA, which is brittleness and low crystallinity. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47152.     

核电厂负刚度阻尼隔震结构的地震响应研究

隔震技术能有效减小核电厂上部结构的加速度响应，但强地震作用下隔震层位移过大会导致管道断裂。本文基于曲面运动原理及预压弹簧伸缩特性提出了一种负刚度阻尼系统，通过球铰在拱球面曲线运动实现负刚度特性，并在弹簧压缩方向提供黏滞阻尼性能。提出了负刚度系统的理论恢复力模型并进行了力学特性分析，设计了负刚度装置并完成了静力试验，结果显示理论恢复力模型与试验结果的一致性较理想。将核电厂负刚度阻尼隔震结构与核电厂隔震结构进行了地震响应对比分析，比较了不同地震波输入下的地震响应。结果表明负刚度阻尼系统可有效同时减小核电厂上部加速度响应和隔震层位移响应。     

Core–shell NTC materials with low thermal constant and high resistivity for wide-temperature thermistor ceramics

Core–shell structures have been proposed to improve the electrical properties of negative-temperature coefficient (NTC) thermistor ceramics. In this work, Al₂O₃-modified Co_1.5Mn_1.2Ni_0.3O₄ NTC thermistor ceramics with adjustable electrical properties were prepared through citrate-chelation followed by conventional sintering. Co_1.5Mn_1.2Ni_0.3O₄ powder was coated with a thin Al₂O₃ shell layer to form a core–shell structure. Resistivity (ρ) increased rapidly with increasing thickness of the Al₂O₃ layer, and the thermal constant (B) varied moderately between 3706 and 3846 K. In particular, Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ ceramic with 0.08 wt% Al₂O₃ showed the increase of ρ double, and the change in its B was less than 140 K. The Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics showed high stability, and their grain size was relatively uniform due to the protection offered by the shell. The aging coefficient of the ceramic was less than 0.2% after aging for 500 hours at 125°C. Taken together, the results indicate that as-prepared Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics with a core–shell structure may be promising candidates for application as wide-temperature NTC thermistor ceramics.     

Quaternäre Metall/Metalloxid‐Katalysatoren als Wandkatalysatoren in Mikroreaktoren für Power‐to‐Gas‐Applikationen mittels kombinatorischer Hochdurchsatzmethoden

Catalysts of quaternary composition have been prepared and tested for the Sabatier process. For catalyst syntheses the following techniques have been used: sol‐gel methods, wet impregnation and incipient wetness impregnation. The Sabatier reaction was carried out at temperatures between 520 K and 670 K, pressures of 15 bar and 30 bar using a mixture H₂:CO₂ of 4:1. Activity screening of the microscale wall catalysts was performed by a custom‐built 10‐fold parallel gas‐flow microreactor setup in sequential operating mode. To analyze the gas phase compositions GC‐FID was used.